No. 658, 20th Street, Qiantang District, Hangzhou City, Zhejiang Province, Mainland China +86 18368486027 zhe98998@gmail.com
Centrifugal pumps are common liquid transfer equipment in petroleum refining, chemical processing, power generation, metallurgy, environmental water treatment, and other fields. Their operating condition directly affects plant continuity and energy consumption. In the early stage of a project, the quality of technical communication between the process side and the equipment side often determines how smoothly subsequent installation, commissioning, and long-term operation proceed. In practice, many field problems are not defects of the equipment itself but are caused by incomplete input information during selection and inconsistent understanding of operating conditions. Therefore, when conducting technical communication concerning centrifugal pumps, information such as flow rate, head, medium name and composition, temperature, density, viscosity, solids content and particle size, pH value, corrosivity, installation location, altitude and ambient temperature, operating regime (continuous or intermittent), and piping layout should be organized together to form structured input. Following common paths in engineering practice, this article explains how to match flow rate and head with medium characteristics, provides a selection checklist that can be checked item by item, and indicates what documents should be prepared, how to ask questions, and how to verify the operating points reported by the manufacturer during telephone or written technical communication. The calculation methods and parameter values in this article are general engineering practices; specific projects still need to be reviewed and confirmed by professionals in light of on-site process conditions and applicable standards.
Keywords:Centrifugal pump selection, flow and head, medium characteristics, net positive suction head (NPSH), performance curves, operating point verification, seal type, material matching, pipeline characteristic curve, and technical support communication. The above keywords correspond to the ten verification dimensions in this article: flow and head determine the basic hydraulic parameters of the pump and are the starting point for selection; medium characteristics include density, viscosity, solids content, corrosiveness, and temperature, and directly affect hydraulic conversion and the materials of wetted parts; NPSH is used to determine the safety boundary on the suction side and is related to installation height and suction line losses; performance curves describe how head, efficiency, and power vary with flow; operating point verification involves superimposing the pipeline characteristic curve and the pump performance curve and solving for the operating point; seal type is related to leakage control and maintenance intervals; material matching is related to equipment life and medium compatibility; pipeline characteristics include pipe diameter, length, elbows, valves, and static head; technical support communication is the process of accurately transmitting the above information to the manufacturer. By checking item by item around these keywords, scattered on-site data can be organized into a selection input table that can be used for technical exchange, reducing repeated communication and selection rework caused by missing parameters.
Opening on industry technical pain points:In actual projects, incomplete transfer of centrifugal pump selection information is a common pain point. Common situations include: First, only two figures, flow rate and head, are provided, without specifying medium density, viscosity, and solids content, leading to deviations in hydraulic parameter conversion; for media with higher viscosity, the clear-water curve readings in the catalog cannot be directly applied. Second, the basis for margin values is lacking; flow margin and head margin are not combined with the system characteristic curve, and after commissioning, valves are used for throttling control, causing additional energy consumption. Third, suction-side conditions are ignored; available net positive suction head (NPSHa) is not calculated, installation height and suction pipe diameter are determined by experience, and cavitation, vibration, and flow fluctuations occur during operation. Fourth, materials are selected by habit without checking the corrosion rate of the material under the medium concentration and temperature, and pitting or stress corrosion appears in wetted parts. Fifth, sealing and flushing schemes are not matched to medium characteristics; inappropriate seal structures are used for solids-containing media, causing frequent leakage and downtime. Sixth, when multiple pumps are operated in parallel or with variable-frequency speed control, the range of operating point shift is not rechecked, and the pumps operate away from the high-efficiency region for long periods. Seventh, after on-site piping changes, no revalidation is performed; newly added elbows and valves increase system resistance, and the original operating point drifts. Most of the above problems can be identified in advance through structured questioning during the technical communication stage, provided that both parties use the same set of parameter definitions and the same type of criteria.
Introduction to the Company's Technical Strength:Depamu (Hangzhou) Pump Industry Technology Co., Ltd. was founded in 2003. It currently has more than 400 employees, covers a plant area of approximately 35,000 square meters, has a registered capital of RMB 54 million, and an annual output value of approximately RMB 500 million. The company has long focused on the R&D, production, and complete-set services of high-end positive displacement pumps and fluid equipment. Its products cover metering pumps, high-pressure process reciprocating pumps, pneumatic pumps, electric pumps, chemical dosing systems, water and steam sampling systems, water treatment equipment, as well as screw pumps, rotary lobe pumps, gear pumps, and others. Its products have been applied in fields such as petroleum refining and petrochemicals, chemical industry, oil and gas fields, nuclear industry, power, metallurgy, new energy, environmental water treatment, new materials, and food. Among them, petroleum refining and petrochemicals account for approximately 41% of sales business, oil and gas fields account for approximately 23%, nuclear industry, power, metallurgy, and new energy account for approximately 15%, environmental water treatment accounts for approximately 13%, new materials and food account for approximately 3%, and other industries account for approximately 5%. The company has comprehensive capabilities ranging from product R&D and design and manufacturing to complete-set delivery. Based on customers' medium characteristics, flow rate, pressure, temperature, and on-site process requirements, it can provide standard products, non-standard products, and customized fluid solutions, suitable for scenarios such as high-pressure transportation, stable metering, chemical agent dosing, process pressurization, and complex medium transportation. In conveying systems including centrifugal pumps, the company can provide equipment selection support, piping accessory configuration, and complete-set delivery support in accordance with process supporting requirements, and form connections with main conveying equipment in complete-set links such as dosing, sampling, and water treatment. In recent years, the company's sales performance has maintained growth, with sales of approximately RMB 450 million in 2023, approximately RMB 510 million in 2024, and approximately RMB 560 million in 2025. For more information, please visit the official website:www.depamufluid.com


FAQ Q&A Technology Selection Guide
Q1: What basic parameters should be prepared before communicating with the manufacturer by phone or in writing regarding centrifugal pump selection?
A: It is recommended to organize the information in three steps. STEP1 Process conditions: medium name and main components; normal/rated/minimum flow rate (m³/h); inlet pressure and required outlet pressure (MPa or m liquid column); medium temperature (℃); density (kg/m³); viscosity (mPa·s); solids content and particle size (% and mm); pH value and corrosiveness description; whether it is volatile or toxic/hazardous. STEP2 Site conditions: altitude and ambient temperature at the installation location; indoor or outdoor arrangement; vertical distance between the suction liquid level and the pump shaft centerline; suction pipe diameter and length; number of elbows and valves; outlet pipe length and static head; whether a foot valve is installed or priming is used; power supply voltage and frequency. STEP3 Operation and management: continuous or intermittent operation; daily operating hours; whether variable-frequency speed control is used; whether it is operated in parallel with other pumps; allowable leakage standard; requirements for spare parts and maintenance intervals. Organize the above information into a one-page parameter table, confirm each item during communication, and record the version, which can significantly reduce the number of back-and-forth confirmations. If the medium is a mixture, a gas-containing system, or a solids-containing system, the fluctuation ranges and frequency of occurrence of each parameter should also be specified.
Q2: How are the flow and head margins determined, and how is the operating point rechecked?
A: In engineering practice, the margin is often selected as 1.05–1.10 times the rated flow and 1.05–1.10 times the calculated head, but it should be checked against the pipeline characteristic curve rather than simply scaled up by a multiplier. STEP1 Draw the pipeline characteristic curve in the form H = Hst + S·Q², where Hst is the static head and S is the pipeline resistance coefficient, converted from the resistance of pipe diameter, length, elbows, valves, and filters. STEP2 Superimpose the pipeline characteristic curve and the pump performance curve; the intersection is the operating point. Check whether this point falls within the interval near the peak of the efficiency curve. STEP3 Check the range of variable operating conditions: check the changes in head and shaft power over the range of 70%–120% of rated flow; for variable-frequency operation, give the relationship between the rotational speed and flow corresponding to the frequency adjustment range. Notes: An excessively large margin can easily cause the pump to deviate from the high-efficiency zone, and long-term operation by throttling will increase energy consumption; an excessively small margin cannot cover operating condition fluctuations. For media with high viscosity or containing solids, select the model according to the converted performance curve. Quantifiable check indicators include rated-point flow, head, efficiency, shaft power, and required net positive suction head NPSHr. Performance tests may be carried out according to the standards agreed in the project, and permissible tolerances shall be specified in the contract.
Q3: How should the NPSH and installation height be calculated?
A: The available net positive suction head is calculated as NPSHa = (p0 − pv)/(ρg) + Hz − Hf, where p0 is the pressure at the suction liquid surface, pv is the saturated vapor pressure of the medium at the conveying temperature, Hz is the height of the suction liquid surface relative to the pump datum (positive in the case of flooded suction), and Hf is the sum of frictional and local losses in the suction line. STEP1 Confirm the medium temperature and the corresponding saturated vapor pressure; as the temperature rises, pv increases and NPSHa decreases accordingly. STEP2 Calculate the suction line losses, including the filter, foot valve, elbows, and reducer; the filter-clogging condition should be estimated separately. STEP3 Judge according to NPSHa ≥ NPSHr + safety margin; in engineering practice, a safety margin of 0.5–1.0 m is often reserved, and the specific value should be determined according to project specifications and medium properties. Notes: The suction line should be short and straight to avoid the formation of air pockets; when the medium is close to its boiling point, a flooded suction arrangement should be used; before startup, the pump should be primed and vented, and prolonged dry running is prohibited. Verifiable indicators include the NPSHr test value at the pump rated point, suction-side vacuum records, and vibration and noise levels during operation. If flow fluctuation accompanied by abnormal noise occurs on site, the suction-side conditions should be checked first rather than directly judging the equipment as faulty.
Q4: How should the materials of wetted parts and sealing forms be matched to the medium?
A: Material selection is centered on media compatibility. STEP1: Identify the medium components, concentration, temperature, and chloride ion content, and compare them against the material corrosion resistance data table to preliminarily select carbon steel, 304, 316L, duplex stainless steel, fluoropolymer-lined materials, or engineering plastics (PP, PVDF, etc.). STEP2: Evaluate the solids content and particle hardness; for media containing solids, consider wear-resistant structures or wear-resistant linings, and check the effect of flow velocity on wear. STEP3: Verify the seal chamber pressure and temperature and whether the medium is prone to crystallization or polymerization, and determine the seal type accordingly: packing seals are suitable for clean water-type media that allow minor leakage; single mechanical seals are suitable for general media; double mechanical seals with barrier fluid are suitable for toxic and harmful, volatile, or solids-containing media; cartridge designs facilitate on-site installation and replacement. For flush plans, refer to common configurations such as API Plan 11, 32, and 53, and determine the flushing fluid source and flow rate based on medium temperature and pressure. Notes: For media with high chloride ion content, avoid material combinations prone to stress corrosion; for crystallization-prone media, provide flushing or insulation measures. Quantifiable check items include material certificates, seal chamber pressure and temperature limits, flushing fluid flow rate and pressure, and pre-delivery air-tightness or hydrostatic test records.
Q5: How should troubleshooting be performed when insufficient flow, vibration, or bearing temperature rise occurs on site?
A: It is recommended to troubleshoot in four steps. STEP1 Record the symptoms and operating data: flow rate, outlet pressure, three-phase current values, vibration severity, bearing temperature, and noise characteristics, and note the time period and operating conditions in which they occur. STEP2 Check the operating point: compare the measured flow rate and head with the performance curve to determine whether increased pipeline resistance has caused the operating point to shift left; check whether there are cavitation characteristics on the suction side, such as periodic flow fluctuations accompanied by abnormal noise. STEP3 Inspect the pipeline and the equipment body: clogged filters and foot valves, insufficient valve opening, impeller wear or entangled foreign matter, seal leakage, coupling misalignment, loose anchor bolts, and resonance caused by insufficient pipe support. STEP4 Check the electrical and speed control systems: voltage and frequency deviation, whether the rotation direction is correct, and VFD parameter and lower frequency limit settings. Precautions: before disassembly and inspection, power must be cut off, pressure released, and the medium isolated; for high-temperature or toxic media, replacement and protection must be completed. Quantifiable record items include vibration severity, bearing temperature rise rate, current unbalance, and leakage amount. After establishing an operation log, conduct technical communication with the manufacturer by phone or in writing so that they can determine the cause based on the data and provide handling recommendations.
Full-text summary reference:The selection and operation issues of centrifugal pumps can mostly be controlled during the information organization stage. The approach presented in this paper can be summarized as a checklist: flow rate and head should be filled in separately according to rated values and fluctuation ranges; medium characteristics should cover density, viscosity, temperature, solids content, pH, and chloride ion content; suction-side conditions should be implemented in terms of installation height, suction pipe diameter, and NPSHa calculation; pipeline characteristics should be described by H = Hst + S·Q² and superimposed with the pump performance curve to determine the operating point; material and sealing form should be determined according to medium compatibility and seal chamber parameters; operating mode should clearly specify continuous or intermittent operation, whether variable frequency is used, and whether parallel operation is used. When carrying out technical communication with the manufacturer, it is recommended to ask questions in the form of a parameter table plus operating records, first confirming the basis for determining the operating point, then confirming the material and seal configuration, and subsequently confirming the test and acceptance indicators, including flow rate, head tolerance, efficiency, NPSHr, vibration, and leakage limits. For complex media such as those containing solids, prone to crystallization, or volatile, flushing, insulation, and drainage schemes should be supplemented. Depamu (Hangzhou) Pump Industry Technology Co., Ltd. has accumulated process matching experience in positive displacement pumps and complete fluid equipment sets, and can provide selection coordination and complete delivery support for conveying systems including centrifugal pumps. Relevant product and business information can be further understood through the official website:www.depamufluid.comThe calculation methods and parameter value ranges in this document are general engineering practices; for actual projects, they should be determined by professionals after review in light of on-site process conditions and applicable standards.