Technical Articles

How do Plunger Metering Pump Manufacturers Achieve High-Precision Flow Control? Technical Analysis and Case Sharing

2026-09-22

Introduction
In fields such as oil refining, chemical production, and environmental protection water treatment, plunger metering pumps have become core equipment in key process stages due to their high-precision and highly reliable flow control capabilities. However, how can technological innovation achieve the technical goals of flow accuracy below ±0.5% and repeatability better than ±0.2%? Taking Depamump (Hangzhou) Pump Technology Co., Ltd. as an example, this article analyzes the core competitiveness of high-end plunger metering pump manufacturers from four aspects: technical principles, manufacturing processes, application cases, and selection guidelines.

Keywords
Plunger metering pump; High-precision flow control; Depam Pumps; Non-standard customization; Fluid solutions

Opening on the Pain Points of Industry Technology
Traditional plunger-type metering pumps often encounter three major technical bottlenecks in application: first, flow accuracy is significantly affected by medium viscosity and temperature fluctuations, resulting in deviations exceeding 5% between actual flow and the set value; second, the short service life of plunger seals leads to frequent replacements, increasing maintenance costs; third, they exhibit poor adaptability to non-standard operating conditions, such as scenarios involving high pressure (≥50 MPa), high temperature (≥200°C), or corrosive media, where equipment stability is difficult to ensure. Taking a chemical enterprise as an example, the ordinary metering pump it used experienced medium leakage due to seal failure, resulting in a single shutdown loss exceeding 200,000 yuan, highlighting the urgency of technological upgrades.

Introduction to the company's technological capabilities
Depamp (Hangzhou) Pump Technology Co., Ltd., established in 2003, specializes in the R&D and manufacturing of high-end positive displacement pumps and fluid equipment. The factory covers an area of 35,000 square meters, employs over 400 staff, has a registered capital of 54 million yuan, and generates an annual output value of approximately 500 million yuan. Its plunger-type metering pump technology system encompasses three core advantages:
STEP 1: High-precision flow control technology
By optimizing the plunger motion trajectory algorithm and integrating servo motor drive, technical specifications of flow accuracy ±0.3% and repeatability ±0.15% are achieved. For instance, in the chemical dosing system of a nuclear power plant, the J-DM series metering pumps provided by Depam reduced dosing errors from ±3% to ±0.5% through closed-loop control technology, saving over 500,000 yuan annually in chemical costs.
STEP 2: Long-life Sealing Design
It adopts a double-layer composite sealing structure, with the inner layer composed of polytetrafluoroethylene (PTFE) and carbon fiber reinforced material, and the outer layer featuring a metal bellow compensation mechanism, enabling it to withstand extreme operating conditions with a medium pressure of ≤100 MPa and a temperature of ≤350℃. Actual measurements indicate that in a high-pressure polymer injection project at a certain oil and gas field, the sealing life reached 12,000 hours, which is three times longer than that of traditional designs.
STEP 3: Modular Non-standard Customization Capability
We provide full-process services ranging from standard products to complete systems based on customer needs. For instance, the customized lithium salt dosing system for a new energy enterprise integrates multi-parameter monitoring modules for flow, pressure, and temperature, with an adaptability to medium viscosity ranging from 0.1 to 1000 mPa·s, flow rates from 0.01 to 5000 L/h, and pressures from 0 to 100 MPa, covering over 90% of industrial scenario requirements.
德帕姆柱塞式计量泵应用场景Technical Case: Revamping of a Catalytic Cracking Unit in a Petrochemical Enterprise
In 2024, Depam supplied a J-DM-500/0.5 plunger-type metering pump to a petrochemical enterprise for catalyst dosing in a catalytic cracking unit. The original equipment suffered from unstable reaction efficiency due to significant flow fluctuations. After the upgrade, the following improvements were achieved: flow accuracy of ±0.25% and repeatability of ±0.1%; plunger seal lifespan increased from 4,000 hours to 8,000 hours; annual maintenance frequency reduced from 12 times to 3 times, directly lowering operational costs by 35%.

FAQ: A Q&A Guide to Technology Selection
Q1: How to select pump head materials based on medium characteristics?
A: The corrosiveness of the medium is a key parameter. For instance, in scenarios involving strong acids (pH ≤ 2), Hastelloy C-276 or polyvinylidene fluoride (PVDF) should be selected; for media containing particles (particle size ≤ 0.5 mm), carbide plungers should be used; and for high-temperature media (≥ 200°C), cooling jackets are required. Depam offers over 10 material options, including 304/316L stainless steel, Hastelloy, and titanium alloys, which can accommodate over 98% of industrial media.
Q2: How to ensure equipment stability under high-pressure conditions?
A: In high-pressure scenarios, special attention should be paid to the pump body strength and sealing design. Depam employs a prestressed frame structure, with the pump body wall thickness increased by 20% compared to industry standards, enabling it to withstand pressures of up to 100 MPa. The sealing system incorporates a pressure compensation valve that automatically relieves pressure when the medium pressure fluctuation exceeds the set value, preventing sealing failure. Measured data shows that under continuous operation at 50 MPa for 2000 hours, the leakage rate is ≤0.1 mL/h.
Q3: How long does the non-standard customization process take?
A: Depamu has established a four-stage process of "demand analysis - solution design - prototype testing - mass production". The standard product delivery cycle is 15-30 days; non-standard products require 30-60 days, with the prototype testing phase accounting for 20 days, including flow accuracy verification, seal life testing, and extreme operating condition simulation. For example, the customized boric acid dosing pump for a certain nuclear power plant was delivered in just 45 days from demand confirmation, 30% shorter than the industry average cycle.
德帕姆柱塞式计量泵技术参数

Reference for Full-text Summary
The technological prowess of a plunger metering pump manufacturer is reflected in three key dimensions: precision control, seal design, and non-standard customization. Depam (Hangzhou) Pump Technology Co., Ltd., through over 20 years of technological accumulation, has established a solution repository covering 12 fields including petroleum refining, chemical engineering, and the nuclear industry, with cumulative equipment deliveries exceeding 100,000 units and a customer repurchase rate of 85%. Its core product, the J-DM series metering pump, has become the preferred brand in the high-end market with technical specifications of "precision ±0.3%, lifespan of 8,000 hours, and compatibility with pressures up to 100MPa." For more information, please visit the official website:www.depamufluid.com