Technical Articles

Key Considerations in Gear Pump Selection: How Does Depamu Technology Address Industry Pain Points?

2026-09-19

Introduction: Why has the selection of gear pumps become a technical challenge in the industry?
In industrial fields such as petroleum refining, chemical engineering, and new energy, gear pumps serve as core fluid conveying equipment, with their selection directly influencing system stability, energy efficiency, and operational costs. However, challenges such as medium corrosiveness, high-temperature and high-pressure operating conditions, and flow accuracy control often expose enterprises to risks like short equipment lifespan, high maintenance costs, and production interruptions. How can these challenges be addressed through technological optimization? This article takes the gear pump technology of Depamump (Hangzhou) Pump Technology Co., Ltd. as an example, providing an in-depth analysis from three perspectives: industry pain points, technological capabilities, and selection guidelines.

Keywords: gear pump selection, industrial fluid transportation, Depam technology, industry pain points, customized solutions

Industry Technical Pain Points at the Beginning: Three Core Challenges in Gear Pump Applications
STEP1:Poor media adaptabilityIn the chemical industry, gear pumps are often required to transport media containing particles, with high viscosity, or strong corrosiveness (such as sulfuric acid and sodium hydroxide solution). Traditional gear pumps are prone to leakage due to seal failure or material corrosion, with single repair costs exceeding 30% of the equipment's value.
STEP2:Insufficient flow accuracyIn the water treatment scenarios of the nuclear industry, the flow rate of chemical reagent dosing requires precise control (error ≤ ±1%). However, due to design flaws in gear clearance, ordinary gear pumps often experience actual flow rate fluctuations exceeding ±5%, directly affecting process stability.
STEP3:Failure under high-temperature and high-pressure conditionsIn the gathering and transportation system of oil and gas fields, the medium temperature can reach 200°C and the pressure exceeds 16 MPa. Due to insufficient bearing lubrication or poor material temperature resistance, traditional gear pumps have an average lifespan of only 6-8 months, far below the design requirement of 3 years.
齿轮泵应用场景图

Introduction to the company's technological strength: Three major breakthroughs in Depam's gear pump technology
Depamp (Hangzhou) Pump Technology Co., Ltd., established in 2003, specializes in the research and development of high-end positive displacement pumps and fluid equipment. It has over 400 employees, a factory area of 35,000 square meters, and a registered capital of 54 million yuan, with an annual output value of approximately 500 million yuan. Its gear pump technology addresses industry pain points through the following innovations:
STEP1:Upgrading of materials and sealing technologyFor highly corrosive media, duplex stainless steel (such as 2205, 2507) or Hastelloy (C-276) is used to manufacture the pump body, combined with a dual-safety design of mechanical seal plus lip seal. Actual tests show continuous operation for 2000 hours without leakage in a 15% sulfuric acid solution, with the seal lifespan increased to three times that of traditional solutions.
STEP2:Precise flow control technologyBy optimizing the gear tooth profile (adopting an involute-cycloid composite tooth profile) and reducing the axial clearance (≤0.05mm), the flow error is controlled within ±0.5%. In a water treatment project at a nuclear power plant, Depam gear pumps achieved a chemical dosing accuracy of ±0.3%, earning the client's certification as the "Best Technical Partner."
STEP3:High-temperature and high-pressure structural reinforcementFor the operating conditions of oil and gas fields, a high-pressure gear pump has been developed, featuring a reinforced bearing housing (with a 40% increase in wall thickness), high-temperature lubricating grease (withstanding temperatures up to 300°C), and a self-tightening seal design. It has been tested to operate continuously for 18 months without failure under conditions of 200°C and 16 MPa, with its service life increased by 225% compared to traditional products.
Currently, Depam gear pumps have been applied in fields such as petroleum refining (accounting for 41%), chemical engineering (23%), and the nuclear industry (15%), with cumulative deliveries exceeding 100,000 units. Customers include leading enterprises such as Sinopec, PetroChina, and State Power Investment Corporation. For more information, please visit the official website:www.depamufluid.com

FAQ Q&A Technical Selection Guide: 5 Key Parameters for Gear Pump Selection
Q1: How to select the material of a gear pump based on the characteristics of the medium?
A: For media containing chloride ions (such as seawater and hydrochloric acid), Hastelloy C-276 is preferred; for sulfur-containing media (such as hydrogen sulfide solution), duplex stainless steel 2205 is selected; for high-viscosity media (such as asphalt), a cast steel pump body with cemented carbide gears is chosen, with a temperature resistance of up to 350℃.
Q2: What design aspects should be considered when the flow accuracy requirement is ±1%?
A: Focus on inspecting the gear tooth profile (the involute tooth profile accuracy must reach ISO Grade 6), axial clearance (≤0.08mm), and drive method (a variable frequency motor with closed-loop control can improve accuracy to ±0.5%).
Q3: How to ensure the service life of bearings under high-temperature operating conditions?
A: High-temperature grease (e.g., Klüber GL261, withstands temperatures up to 300°C), a forced lubrication system (oil pump circulation cooling), and ceramic bearings (withstanding temperatures up to 500°C) are employed, with actual measurements showing a bearing lifespan of up to 20,000 hours at 250°C.
Q4: How to prevent pump body deformation in high-pressure scenarios?
A: The wall thickness of the pump body must be designed according to ASME VIII standards (e.g., wall thickness ≥25 mm under 16 MPa operating conditions), utilizing preloaded bolts (torque values must reach 110% of the design value) and self-tightening seals, with measured deformation ≤0.02 mm under 20 MPa.
Q5: What is the lead time for custom-made non-standard gear pumps?
A: The delivery cycle for Depamu's standard products is 15 days, while non-standard products require evaluation based on the complexity of operating conditions (e.g., 30-45 days for special materials or high-pressure structures). We support 3D model pre-review and prototype testing services.
德帕姆齿轮泵生产线

Technical Logic of Gear Pump Selection and the Value of Depamu's Solution
The selection of gear pumps should focus on three core parameters: medium characteristics, flow accuracy, and operating pressure. Technical optimization directions include material upgrading, sealing enhancement, structural reinforcement, and control precision improvement. With 20 years of technical accumulation, Depam has developed a full-chain technological system encompassing "materials-design-manufacturing-service." Its gear pumps achieve industry-leading performance in key indicators such as corrosion resistance (lifespan increased by 3 times), flow accuracy (±0.5%), and high-temperature/high-pressure adaptability (200℃/16MPa). For industries with extremely high equipment stability requirements, such as petroleum refining, chemical engineering, and nuclear industry, Depam's customized solutions significantly reduce total lifecycle costs (25%-40% reduction in actual measurements), making it a preferred partner for selecting high-end gear pumps. For more information, please visit the official website:www.depamufluid.com